 |
Technical information, Product classification,
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Mainline System | |
| Rated Voltage | Up to 250V ~ |
| Rated Current | Up to 32A |
| Resistance to Impact | Heavy impact (5J) |
| Connection of Adaptors (tap-off units) |
Connected and disconnected when system is energised and load connected |
| Degree of Protection | IP2xD |
| Degree of Pollution | 2 (Non-conductive pollution with temporary conductivity caused by condensation) |
| Rated Impulse Withstand Voltage | 4000V |
| Terminal Block | |
| Model | In-line Connector |
| Rated Voltage | Up to 250V ~ |
| Rated Current | Up to 32A |
| Rated Connecting Capacity | Up to 4 mm² |
| Type of External Wire | Rigid (Solid or Stranded) |
| Number of Wires Connected to Single Terminal | Max 2 x 2.5mm² Max 1 x 4mm² |
| Terminal Identification | L,N,
 |
| Environment for use | Indoor, or enclosed cabinets outdoors with a minimum degree of protection of IP54 (IEC60529) |
| Allowable ambient temperature at maximum allowable current | -5°C to +40°C, the average value over a 24 hour period not exceeding 35°C |
| Maximum Relative Humidity | < 93% R.H. non-condensing |
| Rated continuous current of track conductors at 20°C | 32 Amps a.c. |
| Track material | High impact rigid PVC compound |
| Flammability | Self extinguishing UL 94 – 5VA |
| Conductor Material | Special non-plated copper |
| Conductor Resistance R20 (20°C) | 5 milliohms/m |
| Conductor Impedance Z20 (mean at 20°C) | 5 milliohms/m |
| Insulation Resistance at 500V d.c. for 1 Minute | >50 Mohms/m |
| Dielectric Strength | 3.5kV a.c. for 1 min |
| Impulse Strength | 4kV at 1.2/50 μsec |
| Voltage Drop of Track Conductors at Current Load of: | |
| 20Amps | < 11 mV/A.m |
| 32Amps | < 11 mV/A.m |
| IP Designation | IP 2xD |
| Pollution Degree | 2 |
| Rated Continuous Current of Adaptor at 25°C | 16 Amps |
| Tap-off and Track Conductors Contact Resistance | < 0.4 milliohms |
Wording for the specification
|
SUPPLIED BY Thomas and Betts PRODUCT DESCRIPTION Mainline flexible Power Track System COLOURS Standard colours: - White or Black. GENERAL The contractor shall supply and install Mainline where indicated or noted on drawings. COMPLIANCE The Contractor shall ensure that the Mainline installation complies with the requirements of the local supply Authority. INSTALLATION Mainline can be installed surface-mounted or recessed into third party ducting solutions
|
Wording for the specification |
SUPPLIED BY Ductall Systems PRODUCT DESCRIPTION Ductall 150:50 MT Commercial Trunking A two channel extruded aluminium Commercial Trunking duct measuring 150mm x 50mm. Which incorporates the Mainline Power Track System in the top channel with data reticulated via the lower channel - (Cat 6 compliant). COLOURS Natural anodised is the standard base colour. A Custom Powdercoat finish can be achieved using standard colours in the ‘Dulux’ colour range. GENERAL The contractor shall supply and install the skirting duct system where indicated or noted on drawings. The ducting system shall be supplied and installed complete with all factory made accessories. COVERS Standard Data Cable Cover – as illustrated below or, COMPLIANCE The Contractor shall ensure that the entire skirting wiring duct installation complies with the requirements of the local supply Authority and Austel. All ducting shall be earthed. INSTALLATION The 150:50MT shall be installed surface-mounted or semi-recessed The skirting wiring duct shall be fixed to walls alternatively at the top and bottom of the duct at maximum centres of 800mm. All joints (butt, corner and angled) shall be neatly achieved in professional fashion with no visible gaps. Supply and install wiring access via conduits within stud walls, etc. and associated draw wires, to all duct sections throughout this installation. Access shall be separate for each duct channel to maintain electrical isolation.
|
Cross Section of 150:50MT Commercial Trunking
|
Image of the Ductall 150:50MT Commercial Trunking with Mainline Power Track System installed.
|
Wording for the specification |
||||||||
SUPPLIED BY Ductall Systems PRODUCT DESCRIPTION Ductall 125:21 MT Skirting System A single piece extruded aluminium skirting duct measuring 125mm x 21mm, which incorporates the Mainline Power track system either channel depending on the type of installation. The 125:21 skirting can be surface or flush mounted, recessed or supplied as a top-hat recessable duct. Limited data or communication cabling can be reticulated using the lower channel of the Ductall 125:21 skirting system. COLOURS Natural anodised is the standard base colour. A Custom Powdercoat finish can be achieved using standard colours in the ‘Dulux’ colour range. GENERAL The contractor shall supply and install the skirting duct system where indicated or noted on drawings. The ducting system shall be supplied and installed complete with all factory made accessories. COMPLIANCE The Contractor shall ensure that the entire skirting wiring duct installation complies with the requirements of the local supply Authority and Austel. All ducting shall be earthed. INSTALLATION The Ductall 125:21 MT Skirting system shall be installed surface-mounted or recessed The Ductall 125:21 MT Skirting system shall be fixed to wall alternatively at the top of the duct at maximum centres of 300. All joints (butt, corner and angled) shall be neatly made in a tradesman like fashion with no visible gaps. Supply and install wiring access via conduits within stud walls, etc. and associated draw wires, to all duct sections throughout this installation. Access shall be separate for each duct channel to maintain electrical isolation. Cross Section of 125:21MT skirting system
|
||||||||
